This patch is an attempt to fix following compilation warning.

In file included from drivers/mtd/chips/cfi_cmdset_0001.c:35:0:
drivers/mtd/chips/cfi_cmdset_0001.c: In function 'cfi_intelext_write_words':
include/linux/mtd/map.h:331:11: warning: 'r.x[0]' may be used uninitialized in this function [-Wmaybe-uninitialized]

I could have used uninitialized_var() too, but didn't used it as the final else
part of map_word_load() is missing. So there is a chance that it might be passed
uninitialized. Better initialize to zero.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

Add missing colons to fix kernel-doc generation warnings.

Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

The current version on mtdoops erase first block of mtdoops partition at each
boot if there is no oops stored in flash. This can wear the flash.

When mtdoops start, find_next_position is called to find the next free entry in
the circular buffer. But if the flash is erased, find_next_position don't find
anything (maxcount == 0xffffffff) and start with the first entry after erasing it.

The scanning that is done in find_next_position already track free/used entries.
So if at the end of the scanning we don't find anything, we can start at the
first entry and erased the entry only if it is marked as used.
Most of this is implemented in mtdoops_inc_counter, so to avoid duplicating
code, if we don't find anything we set position to -1. mtdoops_inc_counter with
increment it, erase the entry if needed and start as before with nextpage = 0
and nextcount = 1).

Also during the scan phase, we use the MTDOOPS_KERNMSG_MAGIC to detect corruped
entries.

Signed-off-by: Matthieu Castet <matthieu.castet@parrot@com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

The flctl can now be probed via device tree setup in addition to the
existing platform data way.

SoC specific setup data is set in the .data member of the OF match, so
kept within the driver itself, while board/user specific setup - like
partitioning - is taken from the device tree.

Actual configuration is added for the SoC sh7372.

Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

The code probes if DMA channels can get allocated and tears them down at
removal/failure if needed.
If available it uses them to transfer the data part (not ECC). On
failure we fall back to PIO mode.

Based on Guennadi Liakhovetski's code from the sh_mmcif driver.

Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Reviewed-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

Some small fixes to avoid sparse and smatch complain. Other cosmetic fixes
as well.

- Change of the type of the member index in struct sh_flctl from signed
to unsigned. We use index by addressing array members, so unsigned is more
concise here. Adapt functions relying on sh_flctl::index.
- Remove a blurring cast in write_fiforeg().
- Apply consistent naming scheme when refering to the data buffer.
- Shorten some unnecessarily verbose functions.
- Remove spaces at start of lines.

Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

The whole gpmi-nand driver has turned to pure devicetree supported.
So the linux/mtd/gpmi-nand.h is not neccessary now. Just remove it,
and move some macros to the gpmi-nand driver itself.

Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

In some configurations of "gpio-nand" RDY-pin may be not connected.
This patch allow to use driver for these configurations. In this case
we are assume that device always ready.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

Use the NAND_STATUS_FAIL to replace the hardcode "0x01",
which make the code more readable.

Signed-off-by: Huang Shijie <shijie8@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

Use pr_info() and pr_err() while defining pr_fmt(). This saves a few
characters, joins a few lines, and makes the code a little more readable
(and grep-able).

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

Use pr_fmt instead of PRINT_PREF macro

Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

Use pr_fmt instead of PRINT_PREF macro

Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

Use pr_fmt instead of PRINT_PREF macro

Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

Use pr_fmt instead of PRINT_PREF macro

Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

Use pr_fmt instead of PRINT_PREF macro

Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

Use pr_fmt instead of PRINT_PREF macro

Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

Use KBUILD_MODNAME instead of hardcoding the filename

Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

Use pr_fmt instead of msg macro

Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

This patch removes some code duplication by using
module_platform_driver.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

Few devices like H27UBG8T2CTR have a writesize/oobsize of 8KB/640B.
This means that the maximum oobsize has gone up to 640 bytes and consequently
the maximum ecc placement locations have also gone up to 640.

Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

Use relaxed variants of readl/writel accessors. readl/writel io accessors use
explicit dsb instruction which causes stalls in the processor core resulting
several cycles of delay for each access

Use relaxed variants where ever possible. This also results in an improved
read/write performance.

Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

Interruptible wait caused trouble in fsmc hardware state machine if the
application was killed abruptly. To make fsmc operation safe turn wait in to
un-interruptible.

Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

Due to a clash between refactoring and due to loss of a header
file that remained in my working tree the Nomadik stopped
compiling after switching to the FSMC driver. This patch fixes
it up.

Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

Do not use the platform_data to pass resource and be smart in the drivers.
Just pass it via resource

Switch to devm_request_and_ioremap at the sametime

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-By: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

The nomadik_nand driver is really just a subset of the FSMC
NAND driver, and there are no users anymore so let's delete
it.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

The Nomadik NAND driver is really just a subset of the existing
FSMC driver, so let's switch over to using that driver instead,
since it handles more variants of this chip. The callbacks for
setting up the chip is doing stuff now handled by the FSMC
driver.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

Add a device tree version of the Denali NAND driver. Based
on an original patch from Jamie Iles to add a MMIO version
of this driver.

Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

The Denali controller can also be found in SoC devices attached to a
simple bus.  Move the PCI specific parts into denali_pci so that we can
add a denali_dt that uses the same driver but for a device tree driver
instead of a PCI based device.

Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

Since the introduction of nand_create_default_bbt_descr() (now known as
nand_create_badblock_pattern()) in

  commit 58373ff0

nand_chip.badblock_pattern will be dynamically calculated to the same
1-byte-length pattern that is required by fsl_elbc_nand. This custom
badblock_pattern is no longer needed, then, and its removal may help
facilitate further nand_bbt.c/nand_base.c cleanup in the future (one
down, many to go?)

Anyway, with nand_bbt.c fixed, this effectively reverts:

  commit 452db272
  [MTD] [NAND] fsl_elbc_nand: fix OOB workability for large page NAND chips

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

The pointer returned by kzalloc should be tested for NULL
to avoid potential NULL pointer dereference later. Incorrect
pointer was being tested for NULL. Bug introduced by commit fbcf62a3
(mtd: physmap_of: move parse_obsolete_partitions to become separate
parser).
This patch fixes this bug.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: stable@vger.kernel.org [3.2+]
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

Add DT property "m25p,fast-read" that signalises the particular
chip supports "fast read" opcode.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

Make the error messages more debugging friendly

Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

Simply 'parse_cmdline_partitions': the outer loop iterating over
'partitions' is actually a search loop, it does not execute the inner
loop for each partition, only for the matched partition.

Let's break when search is successful, and move all inner code (relevant
only for the matched partition) outside of the outer loop.

Resulting code is much more readable, and makes the indent level sane.

Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

This patch fixes errors seen in identifying old Samsung SLC, due to the
following commits:

    commit e2d3a35e
    mtd: nand: detect Samsung K9GBG08U0A, K9GAG08U0F ID

    commit e3b88bd6
    mtd: nand: add generic READ ID length calculation functions

Some Samsung NAND with "5-byte" ID really appear to have 6-byte IDs, with
wraparound like:

  Samsung K9K8G08U0D
  ec d3 51 95 58 ec ec d3

  Samsung K9F1G08U0C
  ec f1 00 95 40 ec ec f1

  Samsung K9F2G08U0B
  ec da 10 95 44 00 ec da

This bad wraparound makes it hard to reliably detect the difference
between Samsung SLC with 5-byte ID and Samsung SLC with 6-byte ID.

The fix is to, for now, only use the new Samsung table for MLC. We
cannot support the new SLC (K9FAG08U0M) until Samsung gives better ID
decode information.

Note that this applies in addition to the previous regression fix:

    commit bc86cf7a
    mtd: nand: fix Samsung SLC NAND identification regression

Together, these patches completely restore the previous detection
behavior so that we cannot see any more regressions in Samsung SLC NAND
(finger crossed). With luck, I can get a hold of a Samsung
representative and stop having to cross my fingers eventually.

Reported-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Tested-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

A combination of the following two commits caused a regression in 3.7-rc1
when identifying some Samsung NAND, so that some previously working NAND
were no longer detected properly:

    commit e3b88bd6
    mtd: nand: add generic READ ID length calculation functions

    commit e2d3a35e
    mtd: nand: detect Samsung K9GBG08U0A, K9GAG08U0F ID

Particularly, a regression was seen on Samsung K9F2G08U0B, with the
following full 8-byte READ ID string:

    ec da 10 95 44 00 ec da

The basic problem is that Samsung manufactures both SLC and MLC NAND
that use a non-standard decoding table for deriving information from
their IDs. I have heuristically determined that all the chips that use
the new table have ID strings which wrap around after the 6th byte.
Unfortunately, I overlooked the fact that some older Samsung SLC (which
use a different decoding table) have "5 byte ID strings" which also wrap
around after the 6th byte.

This patch re-introduces a distinction between these old and new Samsung
NAND by checking that the 6th byte is non-zero, allowing both old and
new Samsung NAND to be detected properly.

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Brian Norris <computersforpeace@gmail.com>
Reported-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

jffs2_write_begin() first acquires the page lock, then f->sem. This
causes an AB-BA deadlock with jffs2_garbage_collect_live(), which first
acquires f->sem, then the page lock:

jffs2_garbage_collect_live
    mutex_lock(&f->sem)                         (A)
    jffs2_garbage_collect_dnode
        jffs2_gc_fetch_page
            read_cache_page_async
                do_read_cache_page
                    lock_page(page)             (B)

jffs2_write_begin
    grab_cache_page_write_begin
        find_lock_page
            lock_page(page)                     (B)
    mutex_lock(&f->sem)                         (A)

We fix this by restructuring jffs2_write_begin() to take f->sem before
the page lock. However, we make sure that f->sem is not held when
calling jffs2_reserve_space(), as this is not permitted by the locking
rules.

The deadlock above was observed multiple times on an SoC with a dual
ARMv7 (Cortex-A9), running the long-term 3.4.11 kernel; it occurred
when using scp to copy files from a host system to the ARM target
system. The fix was heavily tested on the same target system.

Cc: stable@vger.kernel.org
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Acked-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

Fixes the following sparse warning:
drivers/mtd/onenand/onenand_base.c:3697:5: warning:
symbol 'flexonenand_set_boundary' was not declared. Should it be static?

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>

Fixed parsing end absolute address.

Signed-off-by: Jiri Engelthaler <engycz@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>